-18"hg 12v Dc Vacuum Pump → Hobby/lab Projects (wet Or Dry)


-18

This item has been shown times.

Buy Now

-18"hg 12v Dc Vacuum Pump → Hobby/lab Projects (wet Or Dry):
$23


Achieve -18" Hg vacuum with 12VPump air and liquid/air mixtures (pump system is all plastic and electrically isolated)Maintenance free and setup within a minute9cm x 7cm x 4cm and less than 300gComes with 2.1mm Female DC input connectorMore accessories such as PSU, compatible Hose and PWM controller available - see optionsOverviewSpecificationsFAQSetup Instructions This 12V pump is powerful, small and versatile. It has diverse DIY lab/light industrial/hobby applications from accelerating filtration setups to electronics (e.g. providing suction for SMT pick and place). What creative projects can you imagine?

This pump comes with the following depending on which kit option you decide to purchase: cable with 2.1mm connection; 12V Power Supply Unit; 90cm of Hose with 6mm diameter; PWM controller to attenuate vacuum strength

Please see our store for other products ThinkItMakeIt. Vacuum Range: -18" to 0" Hg (-0.6 to 0 Bar), where 0 is at atmospheric pressure.
Free flow Range: 5-12 LPM (litres per minute)
Dimensions: 7cm x 4cm x 9cm (length x width x height)
Weight: 260g
Motor Voltage Range: 6V to 12V 
Inlet and outlet nozzels are 1/4" barbs 
5 hours continuous operation


You will receive, depending on the kit option purchased:

Option 1: 1x 12V Diaphragm Pump + 1x 2.1mm DC Female Input Connector

Option 2: All items in Option 1 plus 12V (2A DC output) Power Supply Unit (100-240V AC 50/60Hz input). An adapter appropriate to the buyer's country is included free of charge when applicable

Option 3: All items in Option 2 plus 90cm of Hose with 6mm diameter

Option 4: All items in Option 3 plus 1 x PWM controller to set vacuum strenth in range -18" to 0 (where 0 is atmospheric pressure)

Option 5: Only the 12V Diaphragm Pump without any of the accessories

All the components in this kit are new.
For any more questions you might have please contact us on the message system and we'll try and answer all the questions you may have.

Q: Does it matter which way the terminals are connected?
A: Air flow always in the same direction no matter which way the terminals are connected. Minimal assembly is required and no tools are needed. Setup should take 2 minutes.

1. Attach the DC connector leads to the copper terminals located at the top of the of the pump. Note that it doesn't matter which way round the terminals are connected; the air will flow the same direction.

2. Connect your own 12V DC 2A supply with 2.1mm male plug into the DC connector (or skip 1. if you want to connect your supply directly to the pump's terminals).

3. Find the small arrows marked on the pump's plastic inlet (air intake) and outlet (exhaust) barbs.

4. Connect your own 6mm (1/4") internal diameter hose to the pump's inlet.

Note: Please don't use jubilee clips on the hose as they actually create air gaps; 6mm (1/4") internal diameter hose makes a perfect seal onto the pump's barbs without any help.

Posted with Mobile


-18"hg 12v Dc Vacuum Pump → Hobby/lab Projects (wet Or Dry):
$23

Buy Now



Milwaukee 2760-20 M18™ Fuel™ Surge™ 1/4
Milwaukee 2760-20 M18™ Fuel™ Surge™ 1/4" Hex Impact Driver + Xc Red Lith Battery


100pc Mixed Grit 3
100pc Mixed Grit 3" Roll Lock Discs Pads Sanding Roloc Disks Abrasives


Festool 491937 106
Festool 491937 106" Guide Rail Fs 2700 (2700mm)


[new] Self-priming Filter Cartridge Half Gas Organic Vapor Mask Respirator Singl picture
[new] Self-priming Filter Cartridge Half Gas Organic Vapor Mask Respirator Singl


[new] Personal Protection Anti Attack Panic Emergence Safety Alarm Siren With Le picture
[new] Personal Protection Anti Attack Panic Emergence Safety Alarm Siren With Le


[new] 40 X 60mm Safety Signage Warning Sticker High Temperature Don't Touch Caut picture
[new] 40 X 60mm Safety Signage Warning Sticker High Temperature Don't Touch Caut