Bullet Mold Sprue Plate/pin Lube - 2 Oz.


Bullet Mold Sprue Plate/pin Lube - 2 Oz.

This item has been shown 0 times.

Buy Now

Bullet Mold Sprue Plate/pin Lube - 2 Oz.:
$5


mold_lube_4oz

Bullet Mold Sprue Plate/Pin Lube

This item is a 2 ounce bottle of bullet mold lubricant. This lubricant can be used on bullet mold top, sprue plate, alignment pins and pivot screws. It may be used on any mold material -- iron, brass or aluminum.

We have tried many lubes over the years and all but this one had significant drawbacks. A few of the previous lubes and ill effects are listed below:

Beeswax, candle wax etc. -- it works for a while but it will build up and eventually require a thorough cleaning with harsh chemicals or the mold alignment pins will stick from the buildup.

Aluminum based anti-seize compound -- this works better than beeswax but will build up over time and need a full cleaning. This is also messy to use as it seems to get everywhere.

Graphite/moly based anti-seize compound -- Again this works better than beeswax but will build up over time and need a full cleaning. It is messy as well.

None of the above offer all the benefits of the lube offered here:

  • Easy to apply.

  • Negligible build up with multiple applications.

  • When used on the mold top and sprue plate bottom it prevents lead smearing even when the sprue is cut prior to being fully hardened. This allows for faster casting with no lead smear cleanup. This is especially beneficial in the case of aluminum molds as a lead smear can lead to galling and gouging of the mold top as the hard sprue plate is rotated time and time again over a lead smear.

  • Very tidy to use -- no mess as with the anti-seize compounds.

  • Does not need to be applied nearly as often as alternatives. Once for a typical casting session or a couple of times for a long casting session is adequate.
  • Use sparingly - A little goes a long way! This 2 oz jug should last a very long time.

Illustrated instructions are included with the shipment.

Quantity one of the item pictured below is what you get (with instructions) for the buy-it-now price.




On Sep-17-10 at 08:09:06 PDT, seller added the following information:

Check out some of my response for this item!

"Great Lube, it got Better the Hotter the Mold Got..No Smoke" -- "smoken deal.great stuff" -- "got it today,tried it today.This stuff is awsome" -- "Fast shipper, works great, if you cast you need to buy from this seller!!!!!"

"Man that stuff works great just like you say. A little goes along way. I just cast about 600 bullets and I only had to lube it at the start of my casting. It lasted the whole time with out drying up. I have tried using other lubes but this is best by far."



Bullet Mold Sprue Plate/pin Lube - 2 Oz.:
$5

Buy Now



5 Lb Soft Lead, Lead Ingots, Sinkers, Jigs, Split Shot, Musket Balls picture
5 Lb Soft Lead, Lead Ingots, Sinkers, Jigs, Split Shot, Musket Balls


.38 Cal Vintage Wadcutter 6 Cav Mould 142 Grain 1950's Cast Iron Seco? Great Con picture
.38 Cal Vintage Wadcutter 6 Cav Mould 142 Grain 1950's Cast Iron Seco? Great Con


 C452-300-rf Double Cavity Mold picture
C452-300-rf Double Cavity Mold


 358-158-rf Double Cavity Mold picture
358-158-rf Double Cavity Mold


Lyman Ideal Bullet Mold Lead Casting Handle. Comes With Mold 535 R/b picture
Lyman Ideal Bullet Mold Lead Casting Handle. Comes With Mold 535 R/b


Lyman Firearm Reloading 2800382 Mag 25 Digital Furnace (115v) - Bullet Molds picture
Lyman Firearm Reloading 2800382 Mag 25 Digital Furnace (115v) - Bullet Molds