Holidays.net Online Store

Holdays.net Home


March 5th, 2015
Purim

March 8th, 2015
Daylight Saving Time starts

March 8th, 2015
International Women's Day

March 17th, 2015
St. Patrick's Day

March 17th, 2015
Evacuation Day

March 20th, 2015
Vernal equinox

March 21st, 2015
World Day to Eliminate Racial Discrimination

March 21st, 2015
World Poetry Day

March 21st, 2015
International Day of Nowruz

March 21st, 2015
World Down Syndrome Day

March 22nd, 2015
World Water Day

March 23rd, 2015
World Meteorological Day

March 24th, 2015
World Day for Truth concerning Human Rights Violations

March 24th, 2015
World Tuberculosis Day

March 25th, 2015
World Solidarity Day for Detained and Missing Workers

March 25th, 2015
Day to Remember Slavery Victims and Transatlantic Slave Trade

March 25th, 2015
Maryland Day

March 26th, 2015
Prince Jonah Kuhio Kalanianaole Day

March 29th, 2015
Palm Sunday

March 30th, 2015
Seward's Day

March 31st, 2015
César Chávez Day

April 2nd, 2015
World Autism Awareness Day

April 2nd, 2015
Maundy Thursday

April 2nd, 2015
Pascua Florida Day

April 3rd, 2015
Good Friday

April 4th, 2015
Holy Saturday

April 4th, 2015
First day of Passover

April 4th, 2015
United Nations' Mine Awareness Day

April 5th, 2015
Easter Sunday

 



Search:

Clear Coat Table And Bar Top Epoxy Coating, 2 Quarts For Sale

Clear Coat Table And Bar Top Epoxy Coating, 2 Quarts

CRYSTAL CLEAR TABLE TOP EPOXY KIT

Overview: This product is a 100% solid, two component, clear polymer coating that is
mixed at a 1 to 1 ratio by volume. Each kit contains a bottle of resin and
a bottle of hardener. The product cures to a clear, high build, glass like
finish that resists scratching, yellowing and will not distort with age.
Items coated with it will become permanently preserved and protected for your
enjoyment throughout a lifetime. This product will not exhibit blushing or
sweat out under high humidity conditions

Primary use:This product is commonly seen on bar tops and table tops in many bars and
restaurants.

Application:The product should be applied in two stages to clean surfaces. The first stage
is referred to as the seal coat. The seal coat is brushed on in a thin layer
and is used to seal any pores in the surface and prevent air bubbles from
forming in the following flood coats. This stage is followed by the flood
coat, which will flow and self level, clean brushes or squeeges can be used
to help spread the epoxy. Flood coats are applied in 1/8" layers at a time,
as many as desired can be applied, however one to three coats is average for
most table
or bar coatings.

Recoating/Between Layers:Recoating can usually be be done within 4 to 8 hours. If re-coated within this
time period no sanding is necessary between layers. If your previous
layer has fully dried, light sanding with 220 or 320 grit sandpaper is
recommended to achieve good bonding surface. After sanding you should wipe down
with a solvent such as denatured alcohol, acetone orlacquer thinner to
remove any impurities from the surface. (do NOT use mineral spirits)

Imbedding Pictures:Objects, such as pictures, maps etc. can be imbedded in this product during the
pours. Most photo quality paper does not require any special preparation
however sometimes thin paper objects must first be sealed with a white glue or
similar product to prevent the kleer koat from fully penetrating the paper and
causing it to become transparent.

Imbedding Solid Objects (wood, rocks, shells, etc.)All porous materials should first have a seal coat of epoxy applied. This will prevent
air bubbles from occurring in subsequent flood coats. Usually the objects can be set
in place before sealing.

Working Conditions:For best results the product should be used at temperatures from 70-80 degrees F.
The room which you are working should be clean, dry, dust and insect free.
Settling dust can often cause blemishes on the glassy surface.

Exterior Applications:Please note that although this product will resist yellowing better than other epoxies
it is NOT 100% UV resistant. Continuous outdoor UV exposure over months or years
will cause the finish to lose its gloss and cause gradual changes in color.

Coverage:See the coverage charts shown below to calculate the amount you will need for your
area. Remember not to combine seal and flood coat coverage's. Flood coats are
designed to go on approximately 1/8" thick, which is about three times thicker
than that of a seal coat. Example: A 6ft x 4ft bare wood table (24sq ft) would
require 2 Quarts to complete ONE seal coat and about a gallon and a half to complete
ONE flood coat for a total of Two Gallons.

Beginners Notes:This material leaves professional results when applied correctly so take your time and
make sure to beware of these of the common problems we have seen encountered by
first time users.

1. Always make sure that your mixing container is clean and your measuring device is
accurate, this product REQUIRES that you mix at a 1 to 1 ratio by weight or volume,
any variances from this can cause the epoxy to stay soft and not fully cure.

2. This product requires a THOROUGH mixing, usually between 3-4 minutes of solid mixing
without excessive whipping of the mixture(whipping will put lots of air bubbles into
the epoxy). Amounts greater than one gallon at a time can require upto 6-7 minutes
of mixing.

3. After the two components are poured together and stirring begins the mixture will
turn a cloudy white color, this represents areas in which the epoxy has not fully
combined. You must continue to mix until all signs of cloudiness and tiny white lines
have completely disappeared (usually takes 3-4 minutes of
thorough mixing).

4. Always scrape the sides of your mixing container and also the stick during those
3-4 minutes. If UNMIXED epoxy remains on the side of the container or the stick it
will cause wet spots on your finished product if that UNMIXED material falls into
your project......Followup: While pouring your epoxy onto the surface NEVER scrape
the container to remove every last drop, because no matter how thorough you mix
there will always be an unmixed drop on the side of the container that will leave a
wet spot.

Recommendation of Materials Needed For Application:

Safety Gloves - Epoxy can be very sticky

Graduated Mixing Cups - An accurate measurement is extremely important to achieve
optimum curing.

CLEAN Stir Sticks - Any dirt will end up showing on your product. Mixing is very
important, if you whip while mixing you will end up with air bubbles, long thorough
stirs are required.

Applicators - Rubber squeeges are simple to use and leave no air bubbles. Foam brushes
and nylon bristle brushes are preferred with epoxy, make sure there are no loose hairs.

Hair Drier, Heat Gun or Torch - These are used after the pour is completed and the epoxy
is still liquid. A very smooth stroke across about 6-12 inches above the epoxy surface will
burst remaining air bubbles.

Our kleer kote product can be used in any of the above mentioned applications
to achieve a super hard clear finish with great depth.

Available in 2 Part Kits

Mixing Ratio By Volume: 1:1

Coverage Chart

Total Kit Size
(Combined volume of both parts) Coverage for a Seal Coat Coverage for a flood coat 2 Quarts 24 Sq Ft. 8 Sq. Ft. 1 Gallon 48 Sq Ft. 16 Sq. Ft. 2 Gallons 96 Sq Ft. 32 Sq. Ft. 4 Gallons 192 Sq Ft. 64 Sq. Ft. 16 Gallons 768 Sq Ft. 256 Sq. Ft.

" Click Here To See Other Sizes of This Product "

" Click here to send email address for step by step application guide "

" Click Here To Visit My Store " >

E-mail Me if You Don't See The Size or Quantity you want.

I Can Supply All Materials In larger Sizes and Quantities. $33.50/ gallon for order of 100 gallons or more.

Also have mold making rubber, casting plastics, mold making clay in my store.


Clear Coat Table And Bar Top Epoxy Coating, 2 Quarts

This item has been shown 0 times.

Buy Now

Clear Coat Table And Bar Top Epoxy Coating, 2 Quarts:
$31




50 1 Oz Mixing Medicine Cups- Epoxy Airbrush Paint Rod Wrapping Nails Glue & Ink picture
50 1 Oz Mixing Medicine Cups- Epoxy Airbrush Paint Rod Wrapping Nails Glue & Ink


50 1 Oz Mixing Medicine Cups- Epoxy Airbrush Paint Rod Wrapping Nails Glue Ink picture
50 1 Oz Mixing Medicine Cups- Epoxy Airbrush Paint Rod Wrapping Nails Glue Ink


200 1 Oz Mixing Cups - Epoxy Airbrush Rod Wrapping Paint Tattoo Ink Glue + Nails picture
200 1 Oz Mixing Cups - Epoxy Airbrush Rod Wrapping Paint Tattoo Ink Glue + Nails


200 1 Oz Mixing Cups - Epoxy Airbrush Rod Wrapping Paint Tattoo Ink Glue - Nails picture
200 1 Oz Mixing Cups - Epoxy Airbrush Rod Wrapping Paint Tattoo Ink Glue - Nails


300 1 Oz Mixing Cups - Epoxy Airbrush Rod Wrapping Paint Tattoo Ink Glue & Nails picture
300 1 Oz Mixing Cups - Epoxy Airbrush Rod Wrapping Paint Tattoo Ink Glue & Nails


200 1 Oz Mixing Cups - Epoxy Airbrush Rod Wrapping Paint Tattoo Ink Glue & Nails picture
200 1 Oz Mixing Cups - Epoxy Airbrush Rod Wrapping Paint Tattoo Ink Glue & Nails


Alumilite Rubber To Rubber Silicone Mold Release Resin Casting Crafts 2 Fl Oz picture
Alumilite Rubber To Rubber Silicone Mold Release Resin Casting Crafts 2 Fl Oz


50 1 Oz Mixing Cups / Epoxy Airbrush Paint Rod Wrapping Nails Tattoo Ink -reuse? picture
50 1 Oz Mixing Cups / Epoxy Airbrush Paint Rod Wrapping Nails Tattoo Ink -reuse?


25 1 Oz Mixing Cups + Sticks For Resin Epoxy Airbrush Paint Wrapping Nails Glues picture
25 1 Oz Mixing Cups + Sticks For Resin Epoxy Airbrush Paint Wrapping Nails Glues


(100) 1 Oz Mixing Measuring Cups Epoxy Airbrush Rod Repair Paint Glue Tattoo Ink picture
(100) 1 Oz Mixing Measuring Cups Epoxy Airbrush Rod Repair Paint Glue Tattoo Ink