Electric Glue Rc Build Airplane Drone Quadcopter Hexacopter Helicopter Ufo Fix For Sale
Made In USA Highest Quality
The Absolute Best Highest Quality Available
USA SHIP FROM USA
FAST! WE SHIP WORLDWIDE
Specially formulated made for the listed purpose
No Soldering Electrically
Simply apply it as any other glue or paint
and let it dry that's it very easy all without any soldering
Make Electrical Conductive Connections WITHOUT Soldering or Heating
circuit below made with No Soldering Glue wires connected to a power supply
working great all without soldering
Size 0.3 FL.OZ. (9.0 ml ) Container Largest Available Very
High Quality The Best
This easy to use No
soldering glue is suitable for AC & DC circuits. Its conductive formula
effectively seals wire breaks or connections. Suitable for low voltage
applications electronics, hobbyists, and home use. No solder Conductive Glue uses micro carbon
technology to make a glue paint that also conducts electricity. That's right no
need for soldering anymore now that you have this no soldering glue! It acts
like a glue, apply as easy as paint. Put simply, it sticks bits together and
allows electricity to flow between them. This glue is great for repairing
wires, gluing together electronic kits, and really, is a great safe (i.e. no
In one simple step, you can make low voltage AC and DC electrical
connections without soldering or heating.
Make electrical connections quickly
without heat or solder. Attach wires to panels, batteries, etc. using this
amazing product. Conductive non-toxic this product is great for low voltage
electrical connections. Just apply it and allow too dry. No solder glue is the
solution when you can't find the soldering iron, don't want to bother, are out
in the woods, don't quite trust a fifth-grader with a hot iron, can't reach the
connection with both hands, whatever. This stuff conducts low voltage AC and DC
circuits in a permanent bond and is easy to use. Perfect for those really small points hard to reach
sensitive to heat.This should be part of every DIY
Do-it-Yourselfer toolbox in an emergency it's a good idea to have the tools
available at hand to fix the problem.
Instructions included for usage.
Made in USA at a quality facility to insured quality and
This electrically No Soldering Conductive Glue Paint that doesn't produce any toxic fumes.
safe for skin contact.
Make electrical connections without using a soldering
iron or solder or heat.
Just apply it and allow it to dry all without using a
Makes electrical connections carries AC and DC current
the same as if you were soldering with solder. Made in USA
Size 0.3 FL.OZ. (9.0 ml ) Container
Applications for both AC
and DC low voltage projects
Solar Panels, Science Fair Projects,
Audio Systems, Headphone Cords, Car Stereo, TV and Radio Antennas, Home
Electronics, Solar cells, Keypad rubber keypads restore conductivity. Hobby Projects, Cable TV Connections, Flashlights, Christmas
tree lights, Bell Wiring, Model Trains, Boats and Planes, motorcycles and more. • Lead Free •
Simple: One Easy Step • Reliable: Permanent Bond • Highly
Conductive • For Both AC and DC Circuits • Quick and Easy Repairs •Solar Panels • Surface Mount •
Computer Repair • Flex Boards • Connector Repair • Solar
Cell Leads • RF Shielding. Formulation is ideal for bonding all types of low voltage electrical connections.
Electrically conductive bonds to aluminum and steel too!
Highest Quality -
Don't want to solder? Use this No Soldering Glue instead. Just apply
with a toothpick or brush and allow it to dry and bond and you have a solid
Very versatile for many different projects as you can see some examples below
Installing Flex Board on a
gamepad without soldering using our conductive product using toothpick to apply
it easily tape use to hold it in place until dry.
Shielding Guitars RF
The fastest and easiest way to shield instrument pickup cavities,
control cavities and other smaller areas. When connected to electrical ground,
the shielded surfaces help reduce noise, hum and radio interference.
no toxic solvents and additives completely carbon based to avoid corrosion or
oxidizing metal particles over time.
for Shielding Guitars, RFI Shielding etc., Can be used for pickup control cavities and covers and other
smaller areas. Water
soluble until it dries for a neat clean job. The shielded painted surfaces help
reduce noise, hum and radio interference. Works Great to shield out all those
radio waves. You can use it in the pickup cavity and in the electronic cavity
and it cuts the noise down. If you have any routing work inside the control
cavity this is a great solution. It's much easier than lining an area with
copper foil. This is essential for any electronics installation inside a guitar
in which you need to re-shield an area. This is a superb, cost effective and easy to use shielding product. You can use this on all of your Drew & Sebastian
custom guitars and basses etc. Highly
recommended for all, won't peel off like shielding tape. The foil can be
difficult to use properly and if not done correctly will only cause problems.
This product is easy to apply, doesn't require any additional soldering and
creates a good shield against outside interference. You will be glad that you
made the switch. It really saves a lot of time, not just as a quick way to get
a good shield, but with a little planning, it allows you to ground everything
without wires going everywhere. It works great! You can use it for all control
cavities shielding needs.
Remote Controls, Keypads, Keyboards
buttons not working? Solution
THIS PRODUCT CAN FIX THEM!
This product will fix them very easily restores electrical
conductivity to worn carbon contacts on remote controls keypads etc. Remotes
for TVs, DVD players, stereos, keypad etc., Home security keypad, parking
access keypad buttons. Garage door opener, telephone, handsets,
cell phones, microwaves, and calculator’s keypad.Keyboards, game pads remotes, etc.
And many more keypads & remote controls.
If some of the rubber keys on your remote control keypad have stopped
working. Do you have to press really
hard to get them to work?
Malfunctioning buttons are the most common
ailment among aging remotes.
Typically, malfunctioning buttons are caused by a wearing away of the
conductive material on the back of each button,
Without this material, no electrical contact is made with the remote's circuit
Eventually, it becomes difficult or impossible to
change channels, adjust volume or perform any number of remote functions.
Our product restores electrical conductivity to worn
contacts on rubber buttons keys that have worn off making it
unable to complete the circuit.
If some of the keys on your remote have stopped
working or you have to push
really hard to get them to work this will fix them.
Our product coats the rubber keypad with a conductive
solution to restore the conductive material that has worn off over
time to make it function again.
Apply our conductive product to electrically carbon
contacts on the keypads to restore conductivity.
Open your remote control, keypad, keyboard etc. Apply
a thin coat of the product to each of the keypad's carbon contacts on the
keypad. Let the remote fully dry before putting it back together.
Done all fix very easy!
Complete Soldering Kit & How to Solder Video Guide
Check Out This Awesome Product
Everything You Need
Best Service! Best
Quality! Best Packaging! Best Shipping Fastest!