Engine Rebuild Kit - Honda CB750 CB750F CB750K - 1969-1976 - Gasket Set + Seals
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
Engine Rebuild Kit - Honda CB750 CB750F CB750K - 1969-1976 - Gasket Set + Seals:
$78.95
Engine Rebuild Kit - Honda CB750 CB750F CB750K - 1969-1976 - Gasket Set + Seals
Engine rebuild kit for the Honda CB750 form 1969-1976, note the VIN range for the 1976 models in the fitment below. Time to rebuild? If you\'\'re diving in and doing the top end, replacing engine side cover gaskets and replacing some seals this is a great kit to have on hand!
Gasket Set Includes- 12329-300-020 - Breather Cover Gasket - x1
- 12391-300-040 - Cylinder Head Cover Gasket - x1
- 91302-001-020 - O-Ring 30.8mm - x8
- 91305-323-000 - O-Ring 5.8 x 1.9mm - x4
- 91304-286-000 - O-Ring 61.8 x 2mm - x4
- 12251-300-004 - Cylinder Head Gasket - x1
- 12191-300-030 - Cylinder Base Gasket - x1
- 14592-300-000 - Cam Chain Tensioner Gasket - x1
- 18291-254-000 - Exhaust Gasket - x4
- 12209-300-003 - Valve Stem Seal - x8
- 30372-300-300 - Points Cover Gasket - x1
- 11396-300-303 - Clutch Cover Gasket - x1
- 11397-300-303 - Alternator Cover Gasket - x1
- 31282-300-020 - Starter Motor Cover Gasket - x1
- 11395-300-040 - Transmission Cover Gasket - x1
- 11398-300-303 - Oil Pan Gasket - x1
- 15135-300-010 - Oil Pump Gasket - x1
- 91318-300-013 - Sealing Rubber - x6
- 12115-300-000 - Cylinder Stud Gasket - x8
- 91202-216-000 / 91202-302-010 /91202-KFL-841- Clutch Arm Seal - SR type - 13.8 x 24 x 5
- 91206-286-005 /91206-286-013/91206-286-003 - Shift Shaft Seal - 14 x 28 x 7
- 91201-300-003 - Crank Seal - 30 x 42 x 8
- 91215-300-003 - Starting Clutch Gear Seal - 25 x 33 x 4
- 91204-286-003 /91204-286-005 - Kickstart Oil Seal - 18 x 29 x 7
- 91211-286-003- Tach Drive Oil Seal - 4.8 x 14.5 x 4
- 91205-300-005 - Countershaft Seal - 25 x 62 x 8
- Press your seals in straight with a seal driver or a socket with a slightly smaller OD than the seal. Both surfaces must be free of dirt to create an oil tight seal.
- All sealing surfaces for gaskets must be clean and flat to make a proper seal, sometimes non-hardening sealant is necessary.
CB750F Super Sport - 1975-1976 (1976 - Use up to Engine SN 2551567)
CB750K - 1969-1976 (1976 VIN CB750-2540001 - CB750-2575894)
4into1motorcycleparts•Store Policies