This is a great set ofeasy-reassemblingLCD controller kit which is used to turn a bare laptop LCD panel into a desktop/PC monitor. It will be a surprise that your bare LCD will be of good use, and no longer be a waste. Itsupportsmost of the LCD panel from 12.1" to 19" with a LVDS interface and a resolution lower than 1440*900,plug&play kit, no need soldering.
Please remember to leave us your LCD Model Number when placing the order, it is very import for us to prepare the right kit for you.
Size of controller board: 108mmX51mm
Necessary Accessories for turning a LCD to desktop monitor:LCD Controller board, Inverter, LVDS cable, Keypad, VGA cable, Power Adapter. If you already have a VGA cable nor a power adapter, this kit is suitable for you, else there are some other kind of kits for options in our store, click here.
Have a try and you will get great surprise！
Then, are you going to get this kit？
Important Steps to Process your order with this kit:
Step 1:Please provide your LCD panel model no. by sending us the message before offerding this item, so that we can advise a right kit for your LCD. (Usually, the model no. can be found on a sticker on the back of the LCD panel. If needed, disassemble the plastic shell and you will find the sticker）. If possible, please give us as more specification of your LCD as you can. Then wait for our reply.
Step 2: We will give you the reply as soon as possible after carefully selecting and testing the kit by our technical support, and then you can place the order, and pay for it. We will send the package via HongKong Post as soon as possible after cleared payment. (If you prefer express shipping, please contact us to pay additional shipping cost before payment.)
Step 3: Waiting for the package.
We will write corresponding program into the lcd controller board to match your LCD, so this kit will match against one very specific LCD Panel or others that have exactly the samespecification.However, a programmer could help on different LCDs, that is, change the firmware of the LCD controller board by yourself. Be aware that differentLVDS cables and Inverters will be needed to matchdifferent LCDs.
1. Please make sure that your LCD is ok before offerding this item, else you will be responsible for the incompatibility.
2.If you concern much about resolution setting, please reconsider before offerding!
3.We will try our best to prepare the right kit for you, such as writing the corresponding program into the controller board, selecting the suitable LVDS cable and the suitable inverter. But as we don't have an LCDexactlyas yours at hand, we can just test the controller with our own LCD. For yours, you need to test it yourself to check if it works well or not. As you know, there are so many LCDs with many varieties in the market, sometimes we can't promise the exact compatibility. Please consider it before offerding! However, we have gained many success in preparing the kit for our customers in real store. So why not have a try to get surprise!
4.If you are not specialized in electronics or have doubts inoperation, please contact us for instruction, as we are not able to responsible for wrong operation.
5.After finishing the connecting, please don't rush to power on! First, use multi-meter to test whether the GND of the LCD is connected with the GND of the controller board. If not, please check the connection again. If yes, please test whether there is a short circuit between the red wires and black wires of the LVDS cable. If there is a short circuit, it means opposite connection or other errors. Any problem, please feel free to contact us. DIY needs a certain professional knowledge, please kindly take the responsibility of the risk.No metal contact is allowed when powering on the controller board, otherwise short circuit may occur, which may cause unavailability of the controller board.
Example from our French Customer radicalboy_fr's Project:
Example from (docpot2008-- a Canadian friend's Project ):
Instruction to connect the controller board to the LCD:
1. Take away the old inverter and old LVDS cable from the LCD panel.
2. Connect the new inverter and LVDS cable to your LCD panel.
3. Connect controller board with PC by VGA cable.
4. Input power of 12V,4A.
We have collected a few of the model no. in the following table which we have gained success forreference. However, no matter your model no. is listed in the table or not, welcome to contact us for more details, we probably will be able to find the solution for you as we are located in a huge electronic market in shenzhen, China.
As we need to select the right inverter and lvds cable to match your lcd for you, so theymay be not the same as that shown in the picture. Hope for your understanding.
Welcome to customize your own kit!
Please make the payment within 5 working days of the close of the sale. If you are offerding on several of our sales which will close on different days, please contact us and you may wait until the last sale you are watching has ended for the payment.
We accept Paypal payment method only. Thank you for your understanding.
Shipping & Handling
1. Worldwide shipping via Airmail from China .
Delivery Time is as follow:
(A) United States / United Kingdom / Australia / Canada: 7 - 25 working days.
(B) Other Countries : Maybe take up to 3-8 weeks, depends on local despatch and your country's strict Custom Inspection .
2. We will send the merchandise out within two Business day ter we receive the Payment.
3. We will ship worldwide except the following regions: INDIA, Macau, China, Vietnam, Indonesia, Nigeria (please check beforehand).
Notice : Customs Duties Import taxes and Customs Duties in your country are NOT INCLUDED in the item price or shipping charges . These charges are the buyer's responsibility. If you have trouble in your country's Customs about your parcel , please contact with us!
We want you to be happy with our products.And your satisfactory is very important to us.
Please contact us if there are any problems and we will do my best to fix it out. Here is our misrepresented & unsatisfied merchandise policy.
1. We accept returns for replacement or refund within 3 days after receipt of item(s). Items MUST be in their original condition, not worn or altered.
2. We DO NOT reimburse the return shipping charge. Refunds will be for the original price paid, and will be issued within 7 business days after receipt of the return.
This item has been shown 10866 times.
Lcd Controller Board Diy Kit - Turn Bare Lcd To Monitor - B.rtmc1b-1(vga+dc): $30