New ENC28J60 W5100 Ethernet LAN MINI Ethernet Network Module for Arduino TE230

When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

New ENC28J60 W5100 Ethernet LAN MINI Ethernet Network Module for Arduino TE230:
$4.92

Mini W5100
W5100 is a versatile single-chip network interface chip, internal integration 10/100 Ethernet controller, mainly used in high integration, high stability, high performance and low cost of embedded systems.Using W5100 can realize no Internet connection of the operating system.W5100 with IEEE802.3 10 base-t and 802.3 u 100 base - TX compatible.W5100 internal integration of the whole hardware, and after many years of market validation of TCP/IP protocol stack, Ethernet medium transport layer (MAC) and physical layer (PHY).Using W5100 don\'t need to consider the control of Ethernet, only need for a simple port (Socket) programming.

A variety of interface can choose: direct bus, indirect bus and the SPI bus.
Support hardware TCP/IP protocol stack, supports TCP, UDP, ICMP and IGMP, IPv4, ARP, PPPoE.
As many as four separate port
Internal integration 16 kbyte transceiver cache
Indicate the output, a variety of information including RX and TX, Full/Duplex, Colision, Link, Speed
Support automatic polar transformation (DMI/MDIX)
3.3 V power supply, IO is compatible with 5 V voltage signal
Take so, double row 2 * 2.0 mm pin 14
Size :5.2x3x1.5cm (length x width x high )

NANO W5100

This add-on module allows you to connect the Arduino Nano to the internet. You get all of the benefits of using the Arduino Nano. It is fully assembled with long pin headers so you don need to purchase and solder the headers separately. you get the same stackable benefits as the Arduino shields and can run the same code.

It is based on the Wiznet W5100 Ethernet chip which a network (IP) stack capable of both TCP and UDP. Use the Ethernet library to write sketches which connect to the internet using the add-on module.

The ETHERNET-NANO connects to an Arduino Nano using female long wire-wrap headers which extend through the board for the breadboard connections. This keeps the pin layout intact and allows another add-on module to be stacked on top or bottom.

The Micro-SD card slot can be used to store files for serving over a network. It is compatible with the Ethernet library for the Arduino 0022 and later. The SD card library is included in the standard Arduino distribution。

The Arduino Nano communicates with both the W5100 and MicroSD card using the SPI bus. This is on digital pins 11, 12, and 13 on the Nano. Pin 10 is used to select the W5100 and pin 4 is used for the MicroSD card. These pins cannot be used for General Purpose Input/Output(GPIO).

Note that because the W5100 and MicroSD card share the SPI bus, only one can be active at a time. If you are using both peripherals in your program, this should be taken care of by the corresponding libraries. If you\'re not using one of the peripherals in your program, however, you\'ll need to explicitly deselect it. To do this with the MicroSD card, set pin 4 as an output and write a high to it. For the W5100, set digital pin 10 as a high output.

The ETHERNET-NANO provides a standard RJ45 ethernet jack.

ENC28J60
controller: Microchip\'s ENC28J60 ethernet / HR911105A
works as server or client
comes with efficient library and examples
direct plug puzzle board, NO soldering needed.
Package included：
1PCS(Depends on your choice!)

Payment must be received in 5 business days of sale closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day maintain high standards of excellenceand strive for 100% customer satisfaction!response is very important to us. We request that you contact us immediately BEFORE you give us neutralor negativeresponse, so that we can satisfactorily address your package need to wait 30 days(US only need 7-10 days),Please take care it.Less than 30 days,we can\'t take a refund.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.