Scout Scope Mount For Mosin Nagant 9130 See Through With Picatinny Rail


Scout Scope Mount For Mosin Nagant 9130 See Through With Picatinny Rail

This item has been shown 0 times.

Buy Now

Scout Scope Mount For Mosin Nagant 9130 See Through With Picatinny Rail:
$59


Brass Stacker™

SCOUT SCOPE MOUNT

Model MN9130SSM

for

Mosin Nagant 91/30′s

SCOPE & RINGS ARE NOT PROVIDED!

Will NOT fit Mosin Nagant M38 or M44’s, See Model MN3844-SSM

***PLEASE READ SPECIFICATIONS & FITMENT NOTES BEFORE PURCHASING***

FEATURES: Allows for mounting of Scout Scope or other long eye relief optics to Mosin Nagant model 91/30′s without the need to drill & tap receiver or make any permanent modifications to firearm. It is designed to fit over rear sight block in order to allow for continued use of the original fixed/iron sights up to 100 meters. The Mount is rigid steel construction with Black Oxide finish. 100% Lifetime Warranty!

SPECIFICATIONS: The Mount will accommodate a front to back (horizontal) pin center distance of 1.39” (35.3mm) to 1.82” (46.7mm) and allows for .039” (1mm) of up and down (vertical) movement. The Mount is designed to fit over rear sight blocks that measure between .750″(19.05mm) and .787″(20.00mm) wide. The total weight including hardware is 5.5 oz. Please note that we have made every reasonable effort to ensure that our Mount will work with the vast majority of 9130’s. If for any reason our Mount does not work with your specific 9130 it can be returned (undamaged) for a full refund.

UNIT:

Mount: CNC laser cut perimeter, die punched holes and mounting slots, form tapped threads and die press formed. 3/32” (13 ga.) thick HR, P&O type CS-B A569 carbon steel; 40000 psi yield strength. Black Oxide plated.

Picatinny Rail: CNC machined to MIL-STD-1913. 8″ long. HR ATSM A36 low carbon steel; 36000 psi yield strength. Black Oxide plated.

Screws: #10-32 x ¼” flat head socket cap screws. Alloy steel; Rc 38-45 hardness.

HARDWARE:

Bolts: M3x.5 X 30mm socket head cap screw. Grade 12.9 medium carbon Q&T alloy steel; Rc 38-44 hardness; 160000 psi yield strength, 177000 psi tensile strength; 1.67 ft lbs tightening torque.

Nuts: M3x.5 Hex Nut. Grade 2 low carbon steel; Rc 32 hardness; 60000 psi tensile strength. Black Oxide plated.

Lock Washers: 3mm cut spring lock washer. Steel. Black Oxide plated.

Flat Washers: 3mm plain flat washer. Steel. Black Oxide plated

TOOLS PROVIDED:

Wrench: 2.5mm short arm hex key. Steel.

Drill: 3.00x41x70mm HSS Jobber. *Note: Drill is provided as a means to clean out or straighten existing pin holes.*

Punch: 3/32” x 7/8” dowel pin. Hardened 4140 alloy steel; Rc 47. ¼” x 2” Aluminum handle. *Note: This punch is not designed to be used on difficult to remove pins such as those soldered in place.*

Complete installation instructions are supplied.

FITMENT NOTES: The pin holes in the rear sight block are often located inconsistently as a result of the original manufacturing process. The two holes are frequently not parallel to each other and may be out of alignment or skewed. The mount can only accomodate so much of this misalignment. You should measure the center distances from pin to pin on both sides and check those with the dimensions listed in the SPECIFICATIONS to ensure that the mount will fit properly. A 3mm drill is provided and can be used to clean out and straighten (to some degree) without enlarging the pins holes once the pins are removed. The pin holes for the rear sight block are generally .118″(3.0mm) in diameter and the supplied 3mm bolts have a nominal OD of .115″(2.92mm). This tight fit along with the use of an appropriate liquid thread locker for the screws and nuts, as well as proper tightening of the same should result in no movement of the Mount during normal firing recoil. Occasionally the rear sight block itself, as it sits on the barrel dovetail underneath, can be out of alignment with the bore axis. This condition, if extreme, can adversely effect how the Mount sits. TOOLS REQUIRED: Safety glasses, heavy gloves, solid work surface or vise, hammer, flat blade screw driver, 7/32” (5.5mm) socket driver or wrench, hand drill, and liquid thread locker. A MAPP (Methyl Acetylene Propadience Propane) gas torch and heavy duty punch may be required to remove existing pins from the rear sight block if they are soldered in place. You can usually find these items at your local hardware or plumbers supply. The application of heat, if done properly, will not cause damage. Keep in mind that you only need to reach the melting point of the solder and that this same temperature was achieved during original construction without adverse effects. Procedure provided in supplied instructions. NOTE: As with ANY scope on ANY mount, should it receive an impact (dropped, hit, etc.) it should not be trusted to be accurate. Thus the SEE-THRU feature of our Mount. You can always still use the original iron or open sights if you feel the Mount has been compromised. Design subject to change without prior notice.

Caution! Improper installation or use may result in damage to property, severe injury, or loss of life. If for any reason this product does not function properly, discontinue use immediately. Always practice proper SAFETY & ensure an UNLOADED condition before beginning installation.

Please call us at 828-665-4427with any installation questions you may have.

It is the sole responsibility of the Buyer to ensure that any/all State/Local laws/ordinances regarding the possesion/use of this product are adhered to. DO NOT order this item if it is prohibited in your area.

SHIPPING: TGR Enterprises, Inc - Normal Business Hours M-F 8:00am-5:00pm ET, Closed on Weekends & Holidays. We ship only USPS and typically First Class. We make every effort to ship items the same or next business day they are ordered and paid for. Our USPS Rural Carrier comes around 10:30am. Therefore, orders received just prior to 10:30am may ship on the next business day as it takes time to process and package the order. Orders received after 10:30am will ship on the next business day.

Terms and Conditions: TGR Enterprises, Inc. and/or its employees are not liable for any injury, loss of life, or damage to property that may result in conjunction with the use of this product. TGR Enterprises, Inc. warrants this product against manufactures defects for the life of the product. Warranty is void if product is disassembled. TGR Enterprises, Inc. reserves the right to repair, replace, refund purchase price, or issue credit on any warranty claims. TGR Enterprises, Inc. reserves the right to change or modify product design without prior notice. Copyright 2011 TGR Enterprises, Inc. All right reserved.

TGR Enterprises, Inc. is a proud supporter of 2nd Amendment rights for every law aoffering American citizen and we appreciate your business! Brass Stacker™ products are designed for use with other O.E.M. products. We have made every reasonable effort to ensure that our products function properly.

Please afford us the opportunity to address any issues you may have with our product by contacting us at any of the following:

TGR Enterprises, Inc.
PO Box 1030
26 Charity Lane
Candler, North Carolina 28715
Telephone: 828-665-4427
Fax: 828-665-7862


Scout Scope Mount For Mosin Nagant 9130 See Through With Picatinny Rail:
$59

Buy Now



Ag2605c Apex Gamechanger Bow Sight 5-pin .019 Apg picture
Ag2605c Apex Gamechanger Bow Sight 5-pin .019 Apg


1933 River's Edge 5 Piece Green Camo Knife Set picture
1933 River's Edge 5 Piece Green Camo Knife Set


River's Edge 205 Ducks Auto Magnet picture
River's Edge 205 Ducks Auto Magnet


Tinm-104 American Expedition Elk Tin Sign Magnet picture
Tinm-104 American Expedition Elk Tin Sign Magnet


Gcnv-103 American Expedition Bald Eagle Graphic Canvas Art picture
Gcnv-103 American Expedition Bald Eagle Graphic Canvas Art


River's Edge 262 Real Firwood 4x6 Picture Frame With Hand Painted 3d Deer Detail picture
River's Edge 262 Real Firwood 4x6 Picture Frame With Hand Painted 3d Deer Detail